HomeMamod Spares and Parts | UK Free Post
Mamod Spares and Parts Produced by Mamod Ltd and Independent Manufacturers in the UK.
Outstanding Customer Service
- Free Mamod engines technical advice from the Mamod Guru.
- Help in gettting Mamod steam engines running properly.
- Independent seller of Mamod spares.
- Spares for Mamod engines.
- Established 2004.
- You've got our phone number! 0777 552 1452
Don't miss out - be sure to visit pages 1 & 2 for all Mamod spares.
- per page
Mamod / Forward Reverse Lever
Suitable for Traction Engine, Steam Roller and Steam Wagon.
SET OF THREE BLACK HARD FIBRE WASHERS
FOR 3/8ths" THREAD DIA. SAFETY VALVE
1/8th-inch diameter Copper Pipe
Suitable for all Mamod copper pipe-work
Steering Spring
This is the tension spring fitted on bottom (TE1A/ SW1) and top (SR1A) of the steering forks.
Genuine Mamod Sight Glass Gasket
Part of the whole assembly that ensures no water leaks from the boiler.
Five Mamod Steam Engine 'O' Rings
This type of 0 ring fits on the top of Mamod Safety Valves.
Both 1/4" and 3/8" valve thread sizes.
Genuine Mamod Decals for the Steam Roller
Make your Canopy great again!
Genuine Mamod Decals for the Steam Wagon
Make your Steam Wagon great again!
Washers For Mamod Engines
Traction Engine/ Steam Roller/Steam Wagon/ Stationary types
Mamod Copper Steering Forks Spring
An absolute necessaity to keep your mobile engine going in a a straight line.
Sight Glass Gasket for Mamod engines
Perspex "glass" window suitable for boiling point temperature.
Repair Insert all Mamod Boilers
Essential when the original Mamod threaded insert has come loose in the boiler.
Boiler Repair Insert for all Mamod boilers 3/16" - Water Level Plug
For replacing your existing damaged boiler thread.
Genuine Mamod Brass screw the Canopy
For Traction Engine and Steam Roller
Hand tightened screw.
Superb Steam Oil for any Mamod Engine
Great little dropper bottle with the right oil.
Perfect to keep your engine running.
Cylinder Bolt Spring Washer for Mamod Engines
Just screw this set through the Forward/Reverse Lever, through the Engine Face Mounting Bracket,
and finally, into the Cylinder face.
Mamod Boiler Repair Insert 3/8"
Suitable for an old type Mamod Stationary Engine where the boiler has the larger Safety Valve with a 3/8th inch thread dia.
Convert Mamod Steering Rod to fit current Steering Forks
For Steering Forks made after 2020.
Brass Steering Rod Fitting for a rod conversion allowing an old rod to fit the new type Mamod Steering Forks.
Mamod Steering Rod Fitting and Nut
Brass Fitting for your pre 2020 Steering Rod.
Mamod Engine plug
For your Mamod engine renovation project.
You can use this to blank off a spare thread such a whistle thread on many engines.
1/4" BSF thread
Mamod Traction Engine and Steam Wagon Forks Spring and Nut
Front suspension spring and nut to fit the Mamod TE1 and TE1a
Soldering Set for your Mamod repair or full renovation
Multicore solder (60% tin,40% lead)
The perfect solution to finish with a wonderful soldered joint to be proud of.
It's the Ultimate Renovation and Repairs Guide!
Find out how to get your engine running properly.
Mamod Steam Roller Forks Steering Damper
The nut is round and has a knurled grippable surface. NOT FOR TRACTION ENGINE
Mamod Repair Sight Glass Kit
Repair/ renovate your Water Level Sight Glass.
Fill the Mamod Boiler and Suck Out Excess
No messing with this little gem.
Retro water level plug...... 3/16" bsw thread.
- For the older model Mamod SE2 and SE3 engines using the 3/16" bsw* threaded plug.
*Please make sure you don't need the 3/16th BSF thread!
For all Mamod Engines 3/16" bsf
Standard Water Level Plug for any Mamod Boiler where one is fitted (except SE2 and SE3).
Mamod Engine "Run it on Air" Adapter - Water Level
- Foot Pump Adapter
- Run your Mamod engine on compressed air.
- Water Level Plug
Mamod Engine "Run it on Air" Adapter - Whistle
Another great bit of innovation from a specialist supplier who has come up with a wizzo idea for testing and trial running your engine. For the whistle position.
Large Chrome Hub Caps Mamod Mobiles
Suitable for the larger dia rear axles. Traction Engines/ Steam Roller/Steam Wagon/
Brass Union Knurled Nut & 0 Ring
You will need this joining-knurled-nut that secures the steam pipe to the boiler
if you have a Kit Type boiler that requires no soldering.
Mamod Burner Tray Shield
For all Mamod engines with Burner Trays that use a Shield:
This fits all solid fuel Burner Trays but not all engines require one.
MAMOD SA1 ROADSTER BACK AXLE
ALSO FOR LIMO / VAN / BUS
Retro Safety Valve 3/8" dia thread
Suitable for SE1 SE2 and SE3 engines.
Mamod (Standard) Safety Valve
This safety valve is compatible with most of the Mamod steam engines
It does not fit the SE1 SE2 or SE3 models.
Mamod Steam Roadster Rear Axle Brass Spacer
Rear Axle requires a spacer on one side
Mamod Roadster Brass Pulley
This is one of the reduction gearing pulleys used on the steam car.
The pulley fits onto the middle axle.
Mamod SP4 Forward/Reverse Lever
This is fitted to the SP4 engines currenty in production.
You will need the Trunnion Screw and Washer to complete the job
King Pins for Mamod Steering Rack
Useful if the King Pins have gone missing
For Old Mamod TE1 Canopy Support Clip
TRACTION ENGINE ONLY:
If you don't know what this is for don't worry about it! But if this is just what you are looking for then you have found ..........
Dimension: For Mamod Crank Shaft Length 47mm.
The shaft diameter is suitable for SE1 SE2 SE2A Stationary engines only.
Not for and mobile engines.
Mamod Fuel Tray Without Heat Protection
Suitable for solid tablets and liquid gel.
Tyres For Mamod Traction Engine
Amazing enhancement for your Mamod TE1A Traction Engine with our premium rubber tyres.
MAMOD TRAILER TYRES SET
If you want a nice-to-look-at, quiet and smooth running Trailer, then this is your deal of the day!
Mamod Flywheel for SA1 Roadster
ROADSTER SA1
This is made for the SA1 vehicle.
DIMENSIONS: OD 1.89 INS/ ID 0.185 INS
Black Flywheel for Mamod SA1 Car variants
This is made for the SA1 type vehicles such as the darker coloured Limousine.
Back Wheel Pulley for Roadster
Back axle pulley for SA1 and derivatives.
Mamod SA1 Windscreen Frame
Designed to go on the Limousine Only
Mamod MSS Whistle
A Mamod Standard Whistle Assembly. Std 1/4 BSF x26 TPI Thread. Fits all Mamod models. Great product suitable for Mamod engines and MSS Locos. Suitable for 0-15psi pressure.
- per page
